Chamberlain CLULP1 Universal Laser Garage Parking Assist

I installed 2 of these units in my garage and am reasonably satisfied with them. My biggest complaint is that the laser dot should be brighter. When entering the garage on a bright summer day it is difficult to see the dot. One of my cars is silver and the other is dark gray. I can't see the dot until it hits my dash which is black in both cars.

The installation was extremely straightforward since the units were attached to a Chamberlain system. One potential "gotcha" is that the wiring that comes with the unit is too short for most garages. You will likely need to buy some additional two conductor wire and spice it to the end of the existing wire.

These units can be used with non-Chamberlain systems or for that matter in a garage without any opener system. Each unit is supplied with a plug in the wall AC adaptor. With the unit attached to the adaptor, the laser stays on all the time. Obviously, I can't comment about how long the unit would last when set up this way.

I bought this unit thinking how could I go wrong with a Chamberlain product. I was wrong, this product is simply a waste of time and money. The laser beam is so small and weak that it's nearly impossible to see and even harder to adjust. I played with it for several hours trying to get the beam to stay in one place long enough to test it. I have it firmly mounted to my ceiling and it moves by itself when trying to adjust it. Then once it's close to where you want it, the beam is so small and weak that you can't see it unless the car is stopped. I would not recommend spending the money on this prodct. There are many more garage parking assist products that work much better and are cheaper.

Buy Chamberlain CLULP1 Universal Laser Garage Parking Assist Now

Don't use those annoying looking "tennis balls" hanging from the ceiling! get this laser parking assist to give your garage that clean sleek look it used to have.

I bought this and installed it on my Chamberlain 3/4 HP Whisper Drive in about 5 minutes. It comes with wires and a power plug. If you are using this with a Chamberlain, you will not need to connect the power plug. All you do is connect 2 wires onto the quick connect plugs on the garage opener that control the safety sensor and that's it.

When you open the garage door, and walk pass the eyes, the laser comes on. The laser shuts off after awhile but once you walk pass the sensors again, the laser comes on. This is perfect if you leave your garage door open, leave and come back. It will trigger the laser no matter what goes through the garage.

The light pulsates and you point and adjust it to where you want it to beam. I wish it was brighter, but it works.

Easy to install, cheap, and works great. I recommend it.

Read Best Reviews of Chamberlain CLULP1 Universal Laser Garage Parking Assist Here

We added these to a Genie screw driver opener, but really if you don't have a Champerlain opener with the dedicated input for these laser lights then all installs will be the same. Your objectives is to:

a. Mount each light on the ceiling with a single screw. We mounted two lights because we had two parking spaces in our garage.

b. Run the wires to the garage door opener control head. We chose to run the wire up through the ceiling and into the crawl space above, and then drill a single 1/4 hole above the door opener and drop them down to the opener through this hole. If you drill the holes at the light end, where the middle of the light will be when mounted, then the wires won't show. A much cleaner installation for very little extra effort.

c. Attach the wires to one of your openers bulb socket so the laser lights go on/off with the garage door opener when you open/close the door, and off when the lights automatically turn off. This is made easy by buying a lamp socket to 110v two prong outlet adapter (about 80 cents at the hardware store), taking out one of the bulbs, screwing in the adapter, connect the wires from the laser lights to a single 110v adapter, and then plug this adapter into the outlet adapter. To keep the same level of light in the garage I replaced the 40 watt incandescent bulb with a 75 watt equiv florescent bulb in the one remaining lamp socket. At this point if you open/close the door you'll see the lasers pulsating (blinking).

d. This is the hardest part. Park your cars exactly where you want them in the garage. Now, aim the laser at a point on your dashboard which is easy to see. The movements are sensitive so this takes time.. but once set it's permanent and will only need to be done again when/if you change your car or the position you want it parked. We chose a spot on the middle of the top dash pad exactly in the middle so as we pull the car in we can watch it "walk" it's way up the dash and to the location we want.

e. Be sure to explain to all drivers how things work. For instance, if the garage door remains open and the lights time out the lasers will go off.. so if the door is open and the car outside, you sweep out the garage or whatever leaving the door open.. then when you put the car inside the laser will not be on. Someone just might keep going forward looking for that light to go on, far enough to hit something in front of the car. :)

Want Chamberlain CLULP1 Universal Laser Garage Parking Assist Discount?

Great idea, however the projected dot is too small and not bright enough to be able to see. If they made one with some power I would snap it up, until then save your money.

Save 27% Off